2 - Fix scsi2sd-util size and sector-size inputs
3 - Fix crash when configured scsi disk starting sector is less than
5 - Update to PSoC Creator 4.0
8 - Fix bug in SCSI Inquiry command for SCSI2 hosts
9 - Added OMTI host quirks mode
10 - Fix for booting from early Mac Plus ROMS
11 - Performance fix when SCSI2 mode is enabled. Some users may need
12 to disable SCSI2 mode if it was incorrectly enabled previously.
13 - Added support for configurable mode pages
14 - Fix for exporting selectionDelay/startupDelay parameters to XML
16 - scsi2sd-util is now built with libudev1 on Linux, as all distros have
17 moved to this version. Users on older Linux distributions will need to
21 - Fixed bug when using sector size that isn't a multiple of 4
23 - Fixed a bug that caused hanging or scsi phase errors on
24 high speed scsi hosts.
25 - Fixed a hang when processing a SCSI RESET in a data phase.
26 - scsi2sd-util: Fixed USB connection problems under Windows 10.
27 - Added option to treat luns as separate devices
28 - Improved boot up time.
32 - Fix bug in SCSI MODE SENSE that returned the wrong mode type
33 - Fixes CDROM emulation
34 - Added selection delay parameter. This should be set to 1ms for older
35 SCSI1 hardware, or 0ms for SCSI2 and Mac Plus.
36 - Upgraded to wxWidgets 3.0.2
37 - Fixed stability/performance issue for sector sizes above 512
38 - Fixed bug that prevented the dvice working after "ejecting" a drive
39 - Upgraded to Cypress PSoC Creator 3.3
40 - Added experimental caching option. This provides a 2x speed up for
41 sequential single-sector writes. It is disabled by default.
42 - Disabled SCSI Disconnect support by default. There's now an option
43 in scsi2sd-util to enable it. It should be left off unless you have
44 a very good reason to enable it.
47 - Added configuration option to allow SCSI2 mode. This option is OFF by
48 default, and should only be enabled when using the SCSI2SD with a SCSI2 host
49 controller. Extra timing delays are added in the default SCSI1/SASI mode to
50 work with slow hardware.
51 - Modified hot-swap card detection to work with longer (60cm) microSD to SD
53 - Fixed off-by-one error in scsi2sd-util "Auto" sector start feature.
54 - Fixed crashes and stalls of scsi2sd-util after saving/loading options
56 - Fixed synchronous transfer request negotiation.
57 SCSI2SD now negotiates back to async transfers instead of simply
58 rejecting the message.
59 - Fixed INQUIRY response to commands lacking an allocation length.
60 - Firmware development updated to PSoC Creator 3.2 (from 3.1)
63 - Added configurable disk geometry.
64 - Added configuration import/export function to scsi2sd-util
65 - scsi2sd-util stability fixes
66 - Fixes to support EMU EMAX1 & 2
69 - Clean up version number mishap (4.2.3 reported as 4.2.2)
70 - Reduce size of mode pages for SCSI1 hosts
71 - Stability improvements whan handling resets during SCSI reads.
74 - Bugfix for failed flash checksums after configing configuration
77 - Improved compatibility with older SCSI1 hosts.
80 - Fix MODE SENSE bug when the allocation length is less than the
82 - Add WRITE BUFFER and WRITE AND VERIFY support.
83 - Fix rare case of very slow performance
86 - Rewrite of the SD card interface to fix compatibility problems.
87 This fixes write issues with Samsung SD cards.
88 - Workaround for SCSI hosts that set 250ms timeouts. Some NCR53C80/53C9X
89 drivers (openbsd, netbsd, and others) set a byte-to-byte timeout which
90 can be exceeded by SD card latency.
91 - Upgrade to PSoC Creator 3.1 and gcc 4.8.4.
92 - Integrated scsi2sd-debug functionality with scsi2sd-util.
95 - Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
96 - Handle glitches of the scsi signals to improve stability and operate with
97 multiple devices on the SCSI bus.
98 - Re-add parity checking. This can be disabled using scsi2sd-config if
100 - Added disconnect/reconnect support during SD card writes.
101 - Preliminary CDROM device support (incomplete)
102 - New configuration method. Data is now stored in flash to allow room for
103 custom VPD tables. The old eeprom configuration is ignored.
104 - Support for up to 4 SCSI targets.
105 - scsi2sd-config and bootloader hosts utilities are replaced by the
106 new scsi2sd-util GUI.
107 - Fix for SD cards with Samsung controllers which expect a "stop" bit
108 in each SD command over SPI.
109 - Hot-swap support. The SD card can be removed whenever it's not in use
110 (ie. the LED must be OFF when the SD card is removed)
113 - Fix blank SCSI ID in scsi2sd-config output.
116 - Allow building utilities on older Linux distros
117 - Resolve missing DLL issues for the Windows utilities
118 - Fix scsi2sd-config crash on Mac.
121 - Fixed several performance issues. Transfer rates up to 2.5MB/s are now
123 - Implemented the READ BUFFER scsi command for performance testing purposes.
124 - Added support for the new "yellow" v4.2 revision boards.
125 - Improved firmware uploading. bootloaderhost can now reset the board back
127 - Display firmware version in scsi2sd-config
128 - Add "--reset" parameter to scsi2sd-config
131 - Critical fix for writes when using non-standard block sizes.
132 - Fix to ensure SCSI phase bits are set atomically.
133 - Always return the requested number of bytes for a REQUEST SENSE command
134 This is required to support the Ensoniq ASR-10.
135 - Decreased (unused) heap and stack sizes to prepare for a memory
137 - Increased the maximum sector size to 8192 bytes.
140 - Fix to SCSI Reset handling to avoid lockups
141 - Bug fixes to improve standards compatibility
142 - Bug fix for Unit Attention Condition, which is now enabled by default.
143 scsi2sd-config can be used to disable it for those systems that
144 truely require it (eg. Mac Plus).
145 - Added Linked commands support.
146 - Added support for configurable sector sizes between 64 and 2048 bytes.
147 The sector size can be set via the MODE SELECT command using a SCSI
148 format utility, or via scsi2sd-config
149 - Powerbook firmware added
152 - Remove hacks around ATN handling, and implement proper select-with-atn
153 support. This fix is essential for communicating with some SCSI hosts.
154 All SCSI2SD users are urged to upgrade to this firmware version.
155 - More fixes to support Apple HD SC Setup (thanks to Doug Brown!)
156 - Fixes to support SCSI1 initiators
157 * Support non-arbitrating initiators.
158 * Support single-initiator option.
159 * Set CCS response format flag in INQUIRY response.
162 - Fixes for better SCSI reset handling
163 - Fix for reading the last sector of the SD card.
164 - Performance improvements. 2.5x read, 2x write performance.
168 - Fixes to support formatting with Apple HD SC Setup. This is very slow,
169 Apple Drive Setup is preferred
170 - Reliability improvement for rejecting unknown SCSI messages.
171 - Reliability improvements for SD card initialisation and reading.
175 - Initial public release.