2 - Added support for configurable mode pages
5 - Fixed bug when using sector size that isn't a multiple of 4
7 - Fixed a bug that caused hanging or scsi phase errors on
9 - Fixed a hang when processing a SCSI RESET in a data phase.
10 - scsi2sd-util: Fixed USB connection problems under Windows 10.
11 - Added option to treat luns as separate devices
12 - Improved boot up time.
16 - Fix bug in SCSI MODE SENSE that returned the wrong mode type
17 - Fixes CDROM emulation
18 - Added selection delay parameter. This should be set to 1ms for older
19 SCSI1 hardware, or 0ms for SCSI2 and Mac Plus.
20 - Upgraded to wxWidgets 3.0.2
21 - Fixed stability/performance issue for sector sizes above 512
22 - Fixed bug that prevented the dvice working after "ejecting" a drive
23 - Upgraded to Cypress PSoC Creator 3.3
24 - Added experimental caching option. This provides a 2x speed up for
25 sequential single-sector writes. It is disabled by default.
26 - Disabled SCSI Disconnect support by default. There's now an option
27 in scsi2sd-util to enable it. It should be left off unless you have
28 a very good reason to enable it.
31 - Added configuration option to allow SCSI2 mode. This option is OFF by
32 default, and should only be enabled when using the SCSI2SD with a SCSI2 host
33 controller. Extra timing delays are added in the default SCSI1/SASI mode to
34 work with slow hardware.
35 - Modified hot-swap card detection to work with longer (60cm) microSD to SD
37 - Fixed off-by-one error in scsi2sd-util "Auto" sector start feature.
38 - Fixed crashes and stalls of scsi2sd-util after saving/loading options
40 - Fixed synchronous transfer request negotiation.
41 SCSI2SD now negotiates back to async transfers instead of simply
42 rejecting the message.
43 - Fixed INQUIRY response to commands lacking an allocation length.
44 - Firmware development updated to PSoC Creator 3.2 (from 3.1)
47 - Added configurable disk geometry.
48 - Added configuration import/export function to scsi2sd-util
49 - scsi2sd-util stability fixes
50 - Fixes to support EMU EMAX1 & 2
53 - Clean up version number mishap (4.2.3 reported as 4.2.2)
54 - Reduce size of mode pages for SCSI1 hosts
55 - Stability improvements whan handling resets during SCSI reads.
58 - Bugfix for failed flash checksums after configing configuration
61 - Improved compatibility with older SCSI1 hosts.
64 - Fix MODE SENSE bug when the allocation length is less than the
66 - Add WRITE BUFFER and WRITE AND VERIFY support.
67 - Fix rare case of very slow performance
70 - Rewrite of the SD card interface to fix compatibility problems.
71 This fixes write issues with Samsung SD cards.
72 - Workaround for SCSI hosts that set 250ms timeouts. Some NCR53C80/53C9X
73 drivers (openbsd, netbsd, and others) set a byte-to-byte timeout which
74 can be exceeded by SD card latency.
75 - Upgrade to PSoC Creator 3.1 and gcc 4.8.4.
76 - Integrated scsi2sd-debug functionality with scsi2sd-util.
79 - Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
80 - Handle glitches of the scsi signals to improve stability and operate with
81 multiple devices on the SCSI bus.
82 - Re-add parity checking. This can be disabled using scsi2sd-config if
84 - Added disconnect/reconnect support during SD card writes.
85 - Preliminary CDROM device support (incomplete)
86 - New configuration method. Data is now stored in flash to allow room for
87 custom VPD tables. The old eeprom configuration is ignored.
88 - Support for up to 4 SCSI targets.
89 - scsi2sd-config and bootloader hosts utilities are replaced by the
91 - Fix for SD cards with Samsung controllers which expect a "stop" bit
92 in each SD command over SPI.
93 - Hot-swap support. The SD card can be removed whenever it's not in use
94 (ie. the LED must be OFF when the SD card is removed)
97 - Fix blank SCSI ID in scsi2sd-config output.
100 - Allow building utilities on older Linux distros
101 - Resolve missing DLL issues for the Windows utilities
102 - Fix scsi2sd-config crash on Mac.
105 - Fixed several performance issues. Transfer rates up to 2.5MB/s are now
107 - Implemented the READ BUFFER scsi command for performance testing purposes.
108 - Added support for the new "yellow" v4.2 revision boards.
109 - Improved firmware uploading. bootloaderhost can now reset the board back
111 - Display firmware version in scsi2sd-config
112 - Add "--reset" parameter to scsi2sd-config
115 - Critical fix for writes when using non-standard block sizes.
116 - Fix to ensure SCSI phase bits are set atomically.
117 - Always return the requested number of bytes for a REQUEST SENSE command
118 This is required to support the Ensoniq ASR-10.
119 - Decreased (unused) heap and stack sizes to prepare for a memory
121 - Increased the maximum sector size to 8192 bytes.
124 - Fix to SCSI Reset handling to avoid lockups
125 - Bug fixes to improve standards compatibility
126 - Bug fix for Unit Attention Condition, which is now enabled by default.
127 scsi2sd-config can be used to disable it for those systems that
128 truely require it (eg. Mac Plus).
129 - Added Linked commands support.
130 - Added support for configurable sector sizes between 64 and 2048 bytes.
131 The sector size can be set via the MODE SELECT command using a SCSI
132 format utility, or via scsi2sd-config
133 - Powerbook firmware added
136 - Remove hacks around ATN handling, and implement proper select-with-atn
137 support. This fix is essential for communicating with some SCSI hosts.
138 All SCSI2SD users are urged to upgrade to this firmware version.
139 - More fixes to support Apple HD SC Setup (thanks to Doug Brown!)
140 - Fixes to support SCSI1 initiators
141 * Support non-arbitrating initiators.
142 * Support single-initiator option.
143 * Set CCS response format flag in INQUIRY response.
146 - Fixes for better SCSI reset handling
147 - Fix for reading the last sector of the SD card.
148 - Performance improvements. 2.5x read, 2x write performance.
152 - Fixes to support formatting with Apple HD SC Setup. This is very slow,
153 Apple Drive Setup is preferred
154 - Reliability improvement for rejecting unknown SCSI messages.
155 - Reliability improvements for SD card initialisation and reading.
159 - Initial public release.