2 - Fix MODE SENSE bug when the allocation length is less than the
4 - Add WRITE BUFFER and WRITE AND VERIFY support.
5 - Fix rare case of very slow performance
8 - Rewrite of the SD card interface to fix compatibility problems.
9 This fixes write issues with Samsung SD cards.
10 - Workaround for SCSI hosts that set 250ms timeouts. Some NCR53C80/53C9X
11 drivers (openbsd, netbsd, and others) set a byte-to-byte timeout which
12 can be exceeded by SD card latency.
13 - Upgrade to PSoC Creator 3.1 and gcc 4.8.4.
14 - Integrated scsi2sd-debug functionality with scsi2sd-util.
17 - Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
18 - Handle glitches of the scsi signals to improve stability and operate with
19 multiple devices on the SCSI bus.
20 - Re-add parity checking. This can be disabled using scsi2sd-config if
22 - Added disconnect/reconnect support during SD card writes.
23 - Preliminary CDROM device support (incomplete)
24 - New configuration method. Data is now stored in flash to allow room for
25 custom VPD tables. The old eeprom configuration is ignored.
26 - Support for up to 4 SCSI targets.
27 - scsi2sd-config and bootloader hosts utilities are replaced by the
29 - Fix for SD cards with Samsung controllers which expect a "stop" bit
30 in each SD command over SPI.
31 - Hot-swap support. The SD card can be removed whenever it's not in use
32 (ie. the LED must be OFF when the SD card is removed)
35 - Fix blank SCSI ID in scsi2sd-config output.
38 - Allow building utilities on older Linux distros
39 - Resolve missing DLL issues for the Windows utilities
40 - Fix scsi2sd-config crash on Mac.
43 - Fixed several performance issues. Transfer rates up to 2.5MB/s are now
45 - Implemented the READ BUFFER scsi command for performance testing purposes.
46 - Added support for the new "yellow" v4.2 revision boards.
47 - Improved firmware uploading. bootloaderhost can now reset the board back
49 - Display firmware version in scsi2sd-config
50 - Add "--reset" parameter to scsi2sd-config
53 - Critical fix for writes when using non-standard block sizes.
54 - Fix to ensure SCSI phase bits are set atomically.
55 - Always return the requested number of bytes for a REQUEST SENSE command
56 This is required to support the Ensoniq ASR-10.
57 - Decreased (unused) heap and stack sizes to prepare for a memory
59 - Increased the maximum sector size to 8192 bytes.
62 - Fix to SCSI Reset handling to avoid lockups
63 - Bug fixes to improve standards compatibility
64 - Bug fix for Unit Attention Condition, which is now enabled by default.
65 scsi2sd-config can be used to disable it for those systems that
66 truely require it (eg. Mac Plus).
67 - Added Linked commands support.
68 - Added support for configurable sector sizes between 64 and 2048 bytes.
69 The sector size can be set via the MODE SELECT command using a SCSI
70 format utility, or via scsi2sd-config
71 - Powerbook firmware added
74 - Remove hacks around ATN handling, and implement proper select-with-atn
75 support. This fix is essential for communicating with some SCSI hosts.
76 All SCSI2SD users are urged to upgrade to this firmware version.
77 - More fixes to support Apple HD SC Setup (thanks to Doug Brown!)
78 - Fixes to support SCSI1 initiators
79 * Support non-arbitrating initiators.
80 * Support single-initiator option.
81 * Set CCS response format flag in INQUIRY response.
84 - Fixes for better SCSI reset handling
85 - Fix for reading the last sector of the SD card.
86 - Performance improvements. 2.5x read, 2x write performance.
90 - Fixes to support formatting with Apple HD SC Setup. This is very slow,
91 Apple Drive Setup is preferred
92 - Reliability improvement for rejecting unknown SCSI messages.
93 - Reliability improvements for SD card initialisation and reading.
97 - Initial public release.