2 - Fix bug in SCSI Inquiry command for SCSI2 hosts
3 - Added OMTI host quirks mode
4 - Fix for booting from early Mac Plus ROMS
5 - Performance fix when SCSI2 mode is enabled. Some users may need
6 to disable SCSI2 mode if it was incorrectly enabled previously.
7 - Added support for configurable mode pages
8 - Fix for exporting selectionDelay/startupDelay parameters to XML
10 - scsi2sd-util is now built with libudev1 on Linux, as all distros have
11 moved to this version. Users on older Linux distributions will need to
15 - Fixed bug when using sector size that isn't a multiple of 4
17 - Fixed a bug that caused hanging or scsi phase errors on
18 high speed scsi hosts.
19 - Fixed a hang when processing a SCSI RESET in a data phase.
20 - scsi2sd-util: Fixed USB connection problems under Windows 10.
21 - Added option to treat luns as separate devices
22 - Improved boot up time.
26 - Fix bug in SCSI MODE SENSE that returned the wrong mode type
27 - Fixes CDROM emulation
28 - Added selection delay parameter. This should be set to 1ms for older
29 SCSI1 hardware, or 0ms for SCSI2 and Mac Plus.
30 - Upgraded to wxWidgets 3.0.2
31 - Fixed stability/performance issue for sector sizes above 512
32 - Fixed bug that prevented the dvice working after "ejecting" a drive
33 - Upgraded to Cypress PSoC Creator 3.3
34 - Added experimental caching option. This provides a 2x speed up for
35 sequential single-sector writes. It is disabled by default.
36 - Disabled SCSI Disconnect support by default. There's now an option
37 in scsi2sd-util to enable it. It should be left off unless you have
38 a very good reason to enable it.
41 - Added configuration option to allow SCSI2 mode. This option is OFF by
42 default, and should only be enabled when using the SCSI2SD with a SCSI2 host
43 controller. Extra timing delays are added in the default SCSI1/SASI mode to
44 work with slow hardware.
45 - Modified hot-swap card detection to work with longer (60cm) microSD to SD
47 - Fixed off-by-one error in scsi2sd-util "Auto" sector start feature.
48 - Fixed crashes and stalls of scsi2sd-util after saving/loading options
50 - Fixed synchronous transfer request negotiation.
51 SCSI2SD now negotiates back to async transfers instead of simply
52 rejecting the message.
53 - Fixed INQUIRY response to commands lacking an allocation length.
54 - Firmware development updated to PSoC Creator 3.2 (from 3.1)
57 - Added configurable disk geometry.
58 - Added configuration import/export function to scsi2sd-util
59 - scsi2sd-util stability fixes
60 - Fixes to support EMU EMAX1 & 2
63 - Clean up version number mishap (4.2.3 reported as 4.2.2)
64 - Reduce size of mode pages for SCSI1 hosts
65 - Stability improvements whan handling resets during SCSI reads.
68 - Bugfix for failed flash checksums after configing configuration
71 - Improved compatibility with older SCSI1 hosts.
74 - Fix MODE SENSE bug when the allocation length is less than the
76 - Add WRITE BUFFER and WRITE AND VERIFY support.
77 - Fix rare case of very slow performance
80 - Rewrite of the SD card interface to fix compatibility problems.
81 This fixes write issues with Samsung SD cards.
82 - Workaround for SCSI hosts that set 250ms timeouts. Some NCR53C80/53C9X
83 drivers (openbsd, netbsd, and others) set a byte-to-byte timeout which
84 can be exceeded by SD card latency.
85 - Upgrade to PSoC Creator 3.1 and gcc 4.8.4.
86 - Integrated scsi2sd-debug functionality with scsi2sd-util.
89 - Fix handling requests for LUNs other than 0 from SCSI-2 hosts.
90 - Handle glitches of the scsi signals to improve stability and operate with
91 multiple devices on the SCSI bus.
92 - Re-add parity checking. This can be disabled using scsi2sd-config if
94 - Added disconnect/reconnect support during SD card writes.
95 - Preliminary CDROM device support (incomplete)
96 - New configuration method. Data is now stored in flash to allow room for
97 custom VPD tables. The old eeprom configuration is ignored.
98 - Support for up to 4 SCSI targets.
99 - scsi2sd-config and bootloader hosts utilities are replaced by the
100 new scsi2sd-util GUI.
101 - Fix for SD cards with Samsung controllers which expect a "stop" bit
102 in each SD command over SPI.
103 - Hot-swap support. The SD card can be removed whenever it's not in use
104 (ie. the LED must be OFF when the SD card is removed)
107 - Fix blank SCSI ID in scsi2sd-config output.
110 - Allow building utilities on older Linux distros
111 - Resolve missing DLL issues for the Windows utilities
112 - Fix scsi2sd-config crash on Mac.
115 - Fixed several performance issues. Transfer rates up to 2.5MB/s are now
117 - Implemented the READ BUFFER scsi command for performance testing purposes.
118 - Added support for the new "yellow" v4.2 revision boards.
119 - Improved firmware uploading. bootloaderhost can now reset the board back
121 - Display firmware version in scsi2sd-config
122 - Add "--reset" parameter to scsi2sd-config
125 - Critical fix for writes when using non-standard block sizes.
126 - Fix to ensure SCSI phase bits are set atomically.
127 - Always return the requested number of bytes for a REQUEST SENSE command
128 This is required to support the Ensoniq ASR-10.
129 - Decreased (unused) heap and stack sizes to prepare for a memory
131 - Increased the maximum sector size to 8192 bytes.
134 - Fix to SCSI Reset handling to avoid lockups
135 - Bug fixes to improve standards compatibility
136 - Bug fix for Unit Attention Condition, which is now enabled by default.
137 scsi2sd-config can be used to disable it for those systems that
138 truely require it (eg. Mac Plus).
139 - Added Linked commands support.
140 - Added support for configurable sector sizes between 64 and 2048 bytes.
141 The sector size can be set via the MODE SELECT command using a SCSI
142 format utility, or via scsi2sd-config
143 - Powerbook firmware added
146 - Remove hacks around ATN handling, and implement proper select-with-atn
147 support. This fix is essential for communicating with some SCSI hosts.
148 All SCSI2SD users are urged to upgrade to this firmware version.
149 - More fixes to support Apple HD SC Setup (thanks to Doug Brown!)
150 - Fixes to support SCSI1 initiators
151 * Support non-arbitrating initiators.
152 * Support single-initiator option.
153 * Set CCS response format flag in INQUIRY response.
156 - Fixes for better SCSI reset handling
157 - Fix for reading the last sector of the SD card.
158 - Performance improvements. 2.5x read, 2x write performance.
162 - Fixes to support formatting with Apple HD SC Setup. This is very slow,
163 Apple Drive Setup is preferred
164 - Reliability improvement for rejecting unknown SCSI messages.
165 - Reliability improvements for SD card initialisation and reading.
169 - Initial public release.