Add second SPI master for 5.2 board

[SCSI2SD.git] / CHANGELOG

diff --git a/CHANGELOG b/CHANGELOG
index 81b3bf8..6b05105 100644 (file)
--- a/CHANGELOG
+++ b/CHANGELOG
@@ -1,6 +1,76 @@
-20150x0x               4.5
+2020XXXX               XXXXX
+       - Fix for invalid CDROM READ TOC responses (Thanks Simon Gander)
+
+20191202               4.8.4
+       - Fix to prevent sending floppy geometry mode page when not configured as
+       a floppy (Thanks Landon Rodgers)
+       - Fix for VMS 5.5-2 Inquiry allocation lengths. Requires setting "vms" quirk
+       mode in the XML config (Thanks Landon Rodgers)
+
+20190610               4.8.3
+       - Improve XEBEC controller support
+       - Add Flexible Disk Drive Geometry SCSI MODE page
+       - Fix SD card hotswap bug
+       - Add scsi mode page 0 support
+       - Fix regression for EMU EMAX
+
+20180926               4.8.1
+       - Fix bug when writing with multiple SCSI devices on the chain
+
+20180416               4.8
+       - Fix Unit Serial Number inquiry page to use return configured serial number
+       - Apple mode pages now only sent when in Apple mode.
+       - Added quirks selection to scsi2sd-util. Apple users should manually fix
+       their settings to use the Apple mode.
+       - Added specific support for XEBEC controllers.
+       - Added a speed selection to scsi2sd-util. Users with older SASI or SCSI1
+       controllers should select the lower speed for stability.
+       - Support for v5.1 hardware boards.
+
+20170501               4.7.1
+       - Fix scsi2sd-util size and sector-size inputs
+       - Fix crash when configured scsi disk starting sector is less than
+       SD card size
+       - Update to PSoC Creator 4.0
+
+20170312               4.7
+       - Fix bug in SCSI Inquiry command for SCSI2 hosts
+       - Added OMTI host quirks mode
+       - Fix for booting from early Mac Plus ROMS
+       - Performance fix when SCSI2 mode is enabled. Some users may need
+       to disable SCSI2 mode if it was incorrectly enabled previously.
+       - Added support for configurable mode pages
+       - Fix for exporting selectionDelay/startupDelay parameters to XML
+       via scsi2sd-util
+       - scsi2sd-util is now built with libudev1 on Linux, as all distros have
+       moved to this version. Users on older Linux distributions will need to
+       compile from source.
+
+20160111               4.6
+       - Fixed bug when using sector size that isn't a multiple of 4
+       (eg. 522 bytes)
+       - Fixed a bug that caused hanging or scsi phase errors on
+       high speed scsi hosts.
+       - Fixed a hang when processing a SCSI RESET in a data phase.
+       - scsi2sd-util: Fixed USB connection problems under Windows 10.
+       - Added option to treat luns as separate devices
+       - Improved boot up time.
+
+
+20151105               4.5
        - Fix bug in SCSI MODE SENSE that returned the wrong mode type
                - Fixes CDROM emulation
+       - Added selection delay parameter. This should be set to 1ms for older
+       SCSI1 hardware, or 0ms for SCSI2 and Mac Plus.
+       - Upgraded to wxWidgets 3.0.2
+       - Fixed stability/performance issue for sector sizes above 512
+       - Fixed bug that prevented the dvice working after "ejecting" a drive
+       - Upgraded to Cypress PSoC Creator 3.3
+       - Added experimental caching option. This provides a 2x speed up for
+       sequential single-sector writes. It is disabled by default.
+       - Disabled SCSI Disconnect support by default. There's now an option
+       in scsi2sd-util to enable it. It should be left off unless you have
+       a very good reason to enable it.
 
 20150813               4.4
        - Added configuration option to allow SCSI2 mode. This option is OFF by