SCSI2SD V5 Compatibility

Computer systems

• Mac LC-III and LC-475
• Mac II running System 6.0.8
• Mac SE/30
• Apple IIgs using Apple II High Speed SCSI controller card
• Symbolics Lisp Machine XL1200, using 1280 byte sectors
  • Symbolics XL1201
• PDP-11/73 running RSX11M+ V4.6
• Microvax 3100 Model 80 running VMS 7.3
• Commodore Amiga 500+ with GVP A530
• Commodore Amiga 500 KS 1.3 with Oktagon 508 SCSI-2 controller
• Amiga 2000 (B2000 rev 6.4 ECS) with DKB RapidFire SCSI 1 card
  • May require bootloader replacement if it only starts up while on USB power.
• Amiga 3000
  • May require bootloader replacement if it only starts up while on USB power.
• Amiga 4000 equipped with CyberStorm PPC using 68pin adapter.
• Atari TT030 System V
• Atari TT running TOS 3.06 with HDDRIVER software version 9.06
• Atari Mega ST 1; TOS 1.04; Protar ProFile 30 external hard drive enclosure (1GB size limitation)
• Atari MEGA STE
  • needs J3 TERMPWR jumper
  • 1GB limit (--blocks=2048000). The OS will fail to read the boot sector if the disk is >= 1GB.
• Atari Falcon, TOS 4.02, HDDRIVER 9.06 driver
• Sharp X68000
  • SASI models supported. See gamesx.com for information on building a custom cable.
  • needs J3 TERMPWR jumper
  • Set to SCSI ID 3. ID0 will not work.
• Compaq XP-1000 Professional Workstation
  • Alpha 21264 CPU, 667MHz, with a QLogic SCSI controller in a PCI slot
• SCSI-based Macintosh Powerbooks (2.5" SCSI2SD)
  • Also reported to work on Thinkpad 860 running Win NT 4.0 PowerPC.
• AT&T 3B2/600
• Sun 2/120 Workstation (Unit Attention disabled)
• Sun 4/50 workstation
• Data General MV/2500DC running AOS/VS
  • Requires changing deviceTypeModifier to 0x4c in XML config file. Configurable deviceTypeModifier is supported from firmware v4.3.
• Applix 1616
• IMS MM/1
• NeXTcube + NeXTSTEP 3.3
• NeXTStation
  • Modified geometry settings are required to avoid "cylinder group too large" errors while formatting. Configurable geometry is supported from firmware v4.3
• Apollo 400/425s running DOMAIN/OS
• Motorola System V/68 R3V7 and R3V8.
  • Since the installation have information about limited number of drives(most of them with custom commands) it requires a pre-installed disk image to be dd-ed on it. Works with MVME167 and MVME177
• Motorola System V/88 R40V4.0 through R40V4.4
  • It requires to describe the disk into a configuration file. The process is described here - http://m88k.com/howto-001.html
• BBC micro/Master with Akhter host adapter
• Sun SparcStation 2 w/ Solaris 2.5.1
• Solbourne S3000
• TI-99/4A
• Myarc Geneve 9640
• SGI Indy
• RM Nimbus

Samplers

• Roland JS-30 Sampler
• Roland W-30
• Roland VS2480
• Roland S-760, S-770
• Roland XV-5080
• Akai S950
• Akai S1000, S2000, S3200, S3000XL, MPC 2000XL, DPS 12
  • SCSI cable reversed on S3200
  • There are compatibility problems with the Akai MPC3000. It works with the alternate Vailixi 3.5 OS with multi-sector transfers disabled.
  • MPC3000 example video
• AKAI S5000 and S6000 with Firmware Version 2.14
• EMU Emulator E4X with EOS 3.00b and E6400 (classic) with Eos 4.01
• EMU E6400 w/ EOS2.80f
• EMU Emax1, Emax 2
  • E-Mu Emax video
  • Emax 2 video
  • To boot the emax you will need to use the internal scsi connection, rear db25 does not support scsi boot
  • Set SCSI2SD "Selection Delay" parameter to 1ms
• E-mu EIIIXP, EIIIXS
• EMU Darwin 8ch hard disk recorder
• Emu ESI2000, ESI4000
• Emu Esi-32
  • Works with power over 50 pin cable
• Ensoniq ASR-X, ASR-10 (from v3.4, 2GB size limit)
  • ASR-10 Requires TERMPWR jumper (applies to pre. 5.0 SCSI2SD boards only)
  • ASR-X resets when writing to devices > 2Gb.
  • ASRX example video
  • ASR10 installation photos
• Ensoniq EPS16+
• Kurzweil K2000R
  • See kurzweil.com for size limits which a dependant on the OS version. Older OS versions have a 1GB limit.
  • SCSI cable reversed
• Kurzweil K2500XS
• Casio FZ-20M
  • Requires TERMPWR jumper. The manual shows the pin25 of the DB25 connector is "not connected".
  • May require scsi2sd-config --apple flag
• Yamaha A5000, A3000, EX5, EX5R, RS7000
• EMU ESI4000 [1] [2]
• Synclavier 9600.
  • Disable Parity. Max size == 9GB.
• Waveframe 1000
  • Max size = 16GB
• Sequential Circuits Studio 440. [3]
  • Max size = 1GB

Other

• HP 16601A, 16700A logic analyzers
• Fluke 9100 series
• Jacquard textile weaving machines - STAUBLI ( JC4,JC5 ), GROSSE ( C12,C13,C14,C20 ), BONAS ( CTR S250 )
  • JC5 requires bootloader replacement.
• Reftek RT-72A Seismic datalogger.
  • 72A-R-005-00.1.pdf
  • rtfm.s3a.13.html
• Konami Simpson's Bowling arcade machine
  • http://forums.arcade-museum.com
• Capcom System III (CPS3)